Dec 30, 2011

Great layout progress, Goose #3 anniversary, Edna repainted

Just a quick post tonight... I've been off a few days for Christmas and had a chance to make great progress on the layout - all 6 new Tortoise installs are completed, the new panel at Telluride is complete, DCC LocoNet troubleshooting at Ridgway is complete, and a new optical sensor installed near the Ridgeway yard crossover (so I can 'see' when a train is clear during switching moves; key because that crossover is mostly hidden).

On the real RGS side of things, Knotts Berry Farm reported that Goose #3 just celebrated her 80th birthday (in fine, operating shape) and business car Edna has a new exterior paint job.  Details about both at on my Remaining Equipment page, which I finally got around to updating.

That page also has some further details about the RGS #20 rebuild, which continues but needs more funds.

Dec 4, 2011

Tortoises again

Wow, the fall is a busy time for our household... I thought I posted my last update here about 2 weeks ago... actually it's been 6!

So, just a brief update... on the layout side I'm back to installing Tortoise turnout motors, which involves a lot of time twisted under various parts of the layout, working upside down to align rather touchy angles on the underside of the layout.  I'm adding 3 new turnout motors at Telluride as well as a completely new panel, so operators there can switch more efficiently in the narrow aisle.  Here's the panel graphics (which was trimmed somewhat after printing; click if the full image isn't showing):


Panels go to Kinko's and are printed in color on cardstock, then laminated, then glued to the fascia.  Holes are drilled for toggles & LEDs then.

During some test op sessions, I discovered that constantly walking to the far end of the penisula to manually throw the turnouts on the run-around tracks got old pretty quickly.  Also, I figured once the depot is built, it'd be hard (and potentially dangerous to the depot model) to reach over it to manually throw a turnout which will be behind it.  So - another motor there.

I suppose an interesting note my aisle design.  Here's the layout design (click if the full image isn't showing):


The layout was designed so you could follow your train in the same aisle as much as possible.  Wider aisle areas were designed in front of Ridgway, Durango, Rico and Dolores - primary switching areas.  For Telluride, I didn't want to clog up the Dolores, so the wye at Vance and switching at Telluride are intended to be done from the left side - in the Telluride-Ophir aisle.  Thus, my turnout motor additions are being done to allow operators to stay in that aisle, and stay out of other ops' way while switching.  It sounds good on paper... eventually I have more test op sessions w/ multiple people and we'll see if my idea works.

Then in Ridgway, also as the result of some test operating, it was suggested I add motors to all the turnouts in the yard ladder, since when you're using the caboose / runaround track, it's hard to physically see the turnout positions behind those cars... especially given the 51" height of the benchwork there.  So, even for those yard turnouts that can be reached, I'm adding turnout motors and indicators on the panel.  So - another 3 Tortorti will be going in there.  The toggles and wiring are complete, and the linkages on the turnouts complete... just need to add the motors now.

Oct 26, 2011

In Which Steven Discovers Capacitance

So, weather's colder now, and I've still got issues with the newly-installed Digitrax DCC system.

The issue at hand is that my BD8 block detectors (from The Signaling Solution), which I love and which worked flawlessly with the old Keller OnBoard command control system, were now working oddly.  A train would move into a block, the detector LED goes on, and all seems well.  But when the train left the block, the LEDs were stuck 'on'.

Well, after checking for the usual stuff - ground loops, or other sources to cause current to flow through the one of the side of the feeders being used with the detectors, I did the unmanly thing and asked for help.  In this case, the designer of the BD8s.

I received a very quick and thorough return email, which suggested the problem was the DCC signal in one feeder causing a small current to flow, through capacitance, in the other feeder.  The solution was to put some distance between the feeders, physically, as much as possible.

This was a bit discouraging, as only the blocks with the longest wiring runs were experiencing problems, and those were (inevitably) the hidden and least-accessible sections.  You know, the part that runs thru the bathroom walls, thru the basement stairs, behind the furnace, and so on.  To keep wiring neat in these locations, the wiring had been neatly bundled together and carefully routed.  But the bundling was causing the problems - the alternating DCC signal in one wire was inducing a charge in the other wire.

I did color code everything rather religiously, so I crawled under the layout and started tracing the white and gray wires, which is the Rail B side (for me) and being used for detection.

Very long story short, I was able to pull all those wires out and re-route them (still neatly) along new paths that (mostly) kept them a couple inches or so away from the Rail A sides.  After finishing half of the first block (a hidden track beneath Durango), I ran a test train, but no change.  I continued working, got the entire run separated, tentatively ran another test train... and WaaLaa!  Properly functioning signals again!

After much crawling and re-wiring, I've now completed about 5 of the 10 or so affected blocks, and these changes have fixed all of them.  It seems almost crazy that just moving a wire run a little would makde a difference, but with DCC it certainly does!

Oct 14, 2011

RGS #20 restoration continues

Linn Moedinger posted here that work on the restoration of RGS #20 is continuing, with lots of tender issues being addressed. The bottom portion of the tank has been replaced by stainless steel, and will be riveted to the repaired top section. The tender frame has been repaired, as well as the trucks, wheels, bearings, etc. Bearing work is also ongoing with the locomotive, and its wheels still need cracks repaired. The firebox is installed and stay bolts are being put in place; the smokebox is also being installed. The boiler will be installed after the smokebox. In a neat move, the main air reservoir wasn't usable so a new one was fabricated, and placed INSIDE the old one (to maintain the original appearance). Linn also notes that donations continue to be needed to fund the work; those are being handled through the CRRM.

And in other news,  I've finally updated my Links page, and the got the Events section current.  I've only got four shows listed there at the moment, and only 1 is directly-narrow-gauge related.  If you know of other events, let me know and I'll add them.

Oct 10, 2011

Weathering continues while the weather holds

When I'm not fixing things around the house, or trying to keep up w/ life, I've been working on updating the website (STILL replacing links from the Denver Public Library) - it's amazing how many Otto Perry shots I've added to my Rolling Stock page... lots of images of many of the K-27s traversing the railroad in the 40s.  I'm about 1/3 thru the 564 photos of the RGS that Otto has on that site.

I'm also trying to finish up the weathering of my stable of Bachmann steamers, with decals, and then layers of dullcote and weathering powders.  I live in IL, and it's about to get cold, wet, and nasty here for the next (cough) months.  Since I don't have a spray booth, spraying happens only in good weather.  That said, it's been amazing here lately - sunny and low 80s - for over a week!

I've also just pulled out an older Sunset brass steamer, and disassembled and starting the weathering process on him.  This is a gloriously-detailed brass model, but i've never really finished the work to make it operational.  It needs weathering, but also electrical work, more weight, a headlight, and other stuff. 

And finally, as the cold sets in, I'll havae to work on DCC conversions for all of these, including working on or adjusting the phosper wipers on all the Bachmann locos, which (mostly) seem to be slightly out-of-place.  This is kinda scary for me... I've never managed to establish a good working relationship with brass axle or driver wipers.  But, I gotta try - these are great runners but need great pickup as well.